METAL ROLL FORMING MACHINE
Zhongtuo roll forming Systems is a "one-stop shop" for all your roll forming needs,enabling our customers to save time and money when buying roll forming machines,to help customers grow.
Zhongtuo roll forming Systems is a "one-stop shop" for all your roll forming needs,enabling our customers to save time and money when buying roll forming machines,to help customers grow.
Shops that run several hat section sizes handle one job more often than any other, the size change. What matters there is what the operator has to touch. This omega channel machine keeps that work at the frame, where the width and height buttons sit. What Buyers Notice in Daily Operation One set of forming…
Contact: Elliot liu
Email: [email protected]
WhatsApp: 008615127728988
Detailed Content

Shops that run several hat section sizes handle one job more often than any other, the size change. What matters there is what the operator has to touch. This omega channel machine keeps that work at the frame, where the width and height buttons sit.
In daily use, the size work stays at the frame, the rolls stay in the machine, and the operator stays outside the line. This omega channel machine is laid out for exactly that.




Width at the Frame Buttons
Strip width is set with buttons on the frame. A size change doesn't mean pulling or replacing the forming rolls.
Height at the Side Buttons
Height is set with buttons on the side of the frame. They sit on the outside, within reach of an operator standing at the machine. Width and height are set at separate points of the frame, each tied to one dimension of the section.
A Size Change, Step by Step
Width and height are set to the values for the next section, and the line goes back to work on the new size. Nothing comes out of the roll stands during this omega channel machine size change.


The line starts at a manual decoiler and runs through feeding and leveling, punching, pre shearing, forming and cutting, then onto a receiving table. Three hydraulic stations support the work, two for punching and one for shearing. Punching and pre shearing come before forming. Cutting comes after forming and works to a measured length.
One main motor drives the forming line and a chain drive carries power to the roll stands. An encoder measures length as the strip runs.
Operator input runs on two channels. Width and height come from buttons on the frame. Hole count and hole positions are entered on the touch screen, which shows Chinese and English. A remote handle comes with the machine.


Section size on this omega channel machine follows the buyer's drawing. The tables below cover the full build.
Material and Profile
| Item | Setting |
|---|---|
| Material | Galvanized steel, cold rolled steel |
| Material thickness | 0.8 to 2.0mm |
| Tensile strength | Up to 440MPa |
| Profile size | Per the buyer's section drawing |
Roll Forming System
| Item | Setting |
|---|---|
| Forming stations | 16 |
| Roller material | Cr12, quenched |
| Roller hardness | HRC58 to 60 |
| Shaft diameter | 60mm |
| Shaft material | 40Cr |
| Shaft hardness | HRC28 to 32 |
| Chain | 20A |
| Main motor power | 14kW |
Punching and Cutting
| Item | Setting |
|---|---|
| Punching hydraulic stations | 2 |
| Shearing hydraulic station | 1 |
| Hydraulic power | 7.5kW |
| Hydraulic oil | Grade 46, 130L |
| Single hole die | 14 × 30 |
| Double hole die | 8 × 20 |
| Die material | Cr12MoV |
| Cutting method | Hydraulic cutting after forming |
| Encoder | Length measurement |
| Cutting length tolerance | 3000mm ± 1.0mm |
Control System
| Item | Setting |
|---|---|
| Control | PLC and touch screen |
| Touch screen | Hole count and hole positions |
| Interface language | Chinese and English |
| Size adjustment | Buttons on the frame |
Decoiler
| Item | Setting |
|---|---|
| Decoiler type | Manual |
| Loading capacity | 4 tons |
| Coil width | 500mm |
| Coil inner diameter | 480 to 550mm, adjustable |
| Coil outer diameter | Up to 1500mm |
Receiving Table
| Item | Setting |
|---|---|
| Table size | 6 × 0.3 × 0.9m |
| Roller diameter | 55mm |
Overall Machine Information
| Item | Setting |
|---|---|
| Production speed | 0 to 30m per minute |
| Speed condition | Depends on hole quantity |
| Voltage and supply | 415V, 50Hz, 3 phase |
| Machine weight | About 10 tons |
| Working space | About 20m × 2.0m × 2.0m |
A build gets matched to the job when the buyer brings the section drawing and sizes, the material and thickness, hole pattern and positions, coil weight and diameter, output targets, the power supply on site, plus delivery and acceptance terms.
The size change is what matters here. One set of forming rolls covers several sizes, width and height set from buttons on the frame, and the rolls stay in place. That is the case this omega channel machine makes.
Contact: Elliot liu
Email: [email protected]
WhatsApp: 008615127728988
Contact Us For More Roll Forming Machine Detailed Information
You can contact us either through phone number 0086-15127728988 within our working hours, or send an email to [email protected], or send an inquiry form to us using "Inquiry Now" option. Our customer representatives will respond as soon as possible.